Audio Lab of Georgia

.60mH COIL AIR CORE 18 awg wire red Rdc 0.38 ohm 43mm od x 26mm id x 18mm h upc 848791003370 LW18-60 18 gauge perfect layer wound air core inductors are an excellent choice for high quality crossover construction. Features fully annealed refined copper wire, baked enamel insulator, and perfect layer construction. The thin enameled wire permits the tightest windings to minimize DCR and air core construction to ensure no hysteresis and saturation distortions.

Mackie Switch 4PDT Push V Snapin

0000162 Mackie Switch 2PDT Push V Snapin, replaces 500-018-00 SWITCH 2PDT PUSH V SNAPIN 2025-08-07 16:34:21 2025-08-07 16:34:37

Knob LG Analog White 100

100k Fender Control Snapin 100K UPC: 717669107079 Item #: 002-7947-000

AC 120V HA48N7476-5R Output: 18.5V x 2 250mA AC Adapter For Mackie 402VLZ4 4-Channel 402-VLZ3 Premium Mic / Line Mixer 802VLZ4 8-Channel Ultra-Compact Analog Mixer HA48N7476-5R HA48N74765R Input: 120V 60Hz 18W Power Supply Cord Cable

5KZY Potentiometer rotary 10K 9mm single 30mm HT no DETENT --9mm Size Insulated Shaft Snap-in

2k CONTROL 2KB SNAP IN 12mm 2k B 30mm shaft plastic slotted D Fender 038716

PRO 12 00497070 Impedance: 8 Ohms Power capacity: 800 W Peak 400 W Program 200 W Continuous Sensitivity: 94.3 dB / 1 W 1 m Usable freq. range: 50 Hz ~ 4 kHz Cone: Kevlar® impregnated cellulose Voice coil diameter: 2.375" / 60.3 mm Voice coil material: 2 layers, thermally bonded copper wire Kapton former Nomex® stiffener Net weight lb. / kg: 9.7 lbs. / 4.4 kg Znom (ohms) 8 Revc (ohms) 6.00 Sd (Square Meters) 0.053 BL (T/M) 12.36 Fo (Hz) 48.4 Vas (liters) 86.4 Cms (uM/N) 219.7 Mms (gm) 49.10 Qms 3.84 Qes 0.588 Qts 0.510 Xmax (mm) 2.5 Le (mH) 0.72 SPL (1W 1m) 94.3 No (%) 1.73% Vd (cu. in. / ml) 16.2 / 266 Pmax (Watts pgm.) 400 Disp (cu. in. / ml) 73 / 1192 12" Packed Weight: 12.13 lb (5.5 kg) Packed Length: 14" (35.56 cm) Packed Width: 13.125" (33.34 cm) Packed Height: 6.75" (17.14 cm)

NAP Digital Convergence Board

LARGE SIGNAL PCB

NAP

This pot is used on the following products: AxSys 212 AX2 POD POD Pro Bass POD Bass POD Pro POD 2.0 all POD XT products POD X3 POD HD POD HD Pro Vetta I & II Duoverb Flextone I II and III and HD147. THIS POT IS NOT TO BE USED TO REPLACE MASTER VOLUME OR OUTPUT POTS on the follow products POD POD 2 POD XT POD XT Pro all Bass POD products all Spider series amps and all Spider Valve series amps. Line 6 recommends these parts be installed by an authorized Line 6 service center. Line 6 assumes no responsibility for any damages done to your amp while installing this part. All sales are final no refunds or exchanges. 01-48-0103 B103

POT MONO 10KB LINEAR TAPER 25MM D-SHAFT. This pot is used to replace delay time repeats tweak tweez and mix functions on DL4 and all other similar functions on the 4 button stompbox modeler pedals. This pot will NOT replace the model select encoder! Line 6 recommends these parts be installed by an authorized Line 6 service center. Line 6 assumes no responsibility for any damages done to your product while installing this part. All sales are final, no refunds or exchanges on parts. 01-48-7103 B103

Standard .062 Pin and Socket Power Connectors Description: 1.57mm Diameter Standard .062 Pin and Socket Crimp Terminal Female with Tin (Sn) Plated Brass Contact 18-24 AWG